EXFO FTB-1 Скачать руководство пользователя страница 325

Страница: 325 / 675

Test Results

NetBlazer

313

Alarms/Errors

IP/UDP/TCP

Errors



IP Chksum

(IP Checksum)

: The IP datagrams received have invalid IP header checksum. Only

available for IPv4.



UDP Chksum

(UDP Checksum)

: The UDP segments received have invalid UDP checksum.



TCP Chksum

(TCP Checksum)

: The TCP segments received have invalid TCP checksum.

ISDN

Alarms



D-Ch Down

(D-Channel Down)

: The Data Link Layer is not in the multiple-frame established state.

Errors



D-Ch FCS

(D-Channel FCS)

: D-Channel Frames have an invalid FCS.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды