EXFO FTB-1 Скачать руководство пользователя страница 76

Страница: 76 / 675

Test Setup - Test Applications

FTB-700G/800 Series

Carrier Ethernet OAM

Carrier Ethernet OAM

The Carrier Ethernet OAM test application supports the following tests:

Ethernet OAM (S-OAM)

MPLS-TP OAM

, and

Link OAM

Ethernet OAM and MPLS TP OAM

The Ethernet Service OAM tests are divided in two main categories:



Performance Monitoring measures parameters such as frame delay,
frame loss, and synthetic loss (Y.1731/MEF).



Connectivity Fault Management provides the capability for detecting,
verifying, and isolating connectivity failure (Y.1731/802.1ag/MEF).



Typical Ethernet OAM and MPLS TP OAM test applications:



Supported Interfaces/Rates: 10M to 10G LAN/WAN.

MIP

FTB-700G/800 Series

Peer MEP

Local MEP

MIP

FTB-700G/800 Series

Local MEP

FTB-700G/800 Series

Smart Loopback with

S-OAM Responder enabled.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды