manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 283

Test Setup - Test Configurator, Timer, and System

NetBlazer

271

Streams - Profile

TX Rate

 / 

Max TX Rate

 indicates the transmission rate for Voice and 

Video profiles, and allows to enter the transmission rate for Data 
profile. The available stream transmission rate will be calculated 
according to the selected TX Mode. The default setting is 100 percent 
for all interfaces at the exception of 10Gig-E WAN which is 92.8571 
percent (depending on the frame format). 

Unit choices are 

%

 (default), 

Mbit/s

, 

Gbit/s

, 

frame/s

, and 

IFG

. 

However 

frame/s

 and 

IFG

 are not available for 

Random

 and 

Sweep

 

frame sizes. 

Frame Count

 is only available with n-Frame Transmit Mode. Enter the 

frame count number: 

1

 (default) to 

267857142857

. 

Shaping

 button 

For 

Burst

 and 

n-Burst

 TX modes.

Burst Duty Cycle (%)

 represents the burst duration within the 

burst period: 

1

 to 

100

 percent (default is 

50

 percent). 

Period

 represents the burst pattern duration: 

1

 to 

8000

 

milliseconds (default is 

1000

 ms). 

Unit

 choices are 

ms

 (default) and 

s

. 

Burst Count

, available with n-Burst TX Mode, represents the 

number of times the burst will be repeated: 

1

(default) to 

255

. 

For 

Ramp

 and 

n-Ramp

 TX modes.

Ramp Nb. of Steps

 represents the number of steps within the 

ramp: 

2

 to 

100

 (default is 

10

). 

Step Time 

represents the duration of each step: 

100

 to 

8000

 

milliseconds (default is 

1000

 ms). 

Unit

 choices are 

ms

 (default) and 

s

. 

Ramp Cycle Count

, available with n-Ramp TX mode only, 

represents the number of times the ramp will be repeated: 

1

(default) to 

255

. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды