EXFO FTB-1 Скачать руководство пользователя страница 291 | Manualshive

Страница: 291 / 675

EXFO FTB-1 Скачать руководство пользователя страница 291

Test Setup - Test Configurator, Timer, and System

NetBlazer

279

Timer

Timer

Allows to automatically start and/or stop the test at a given time or for a
specific duration.

From the

Test

menu, tap

Setup

, and

Timer

.

Timer

Note:

For RFC 2544 and RFC 6349, only

Start Time

and the

ARM

button are

available.



Duration

: Selects the test duration based on the test start time. The test

start time can be either the time the user starts the test or the time the
test is automatically started when the start time is enabled. The

Duration

check box has to be selected to be included in the test timer.

Choices are

15 minutes

(default),

1

,

2

,

4

,

6

,

12

,

24

,

72 hours

,

7 days

,

and

User Defined

.

When

User Defined

is selected, the field next to it becomes available

to enter the test duration using the format: dd:hh:mm:ss.

Note:

Duration cannot be enabled while stop time is enabled. When the test is
started while duration is enabled, the stop time is calculated and the Stop
Time field is updated to indicate the time the test will stop.



Start Time

selects the time the test will automatically start. The

Start

Time

check box has to be selected to be included in the test timer.

Note:

A valid start time has to be subsequent to the current time.

«
...
289
290
291
292
293
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды