manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 500

Test Functions

488

FTB-700G/800 Series

OH - SONET/SDH

Transport OH - Section/RS 

A1 

and

 A2

: Framing. The value should be hexadecimal 

F6

 for A1 and 

28

 for A2. They must appear in every STS-1/STM-1 frame of a 

composite signal. 

SONET: Provide frame alignment of each STS-1 frame within a 
composite signal (STS-1 to STS-n). 

SDH: Indicate the beginning of the STM-N frame. 

J0/Z0

J0

: The J0 (Trace) byte is used to trace the origin of an STS-1/STM-1 

frame as it travels across the SONET/SDH network. This byte is only 
defined for the first STS-1/STM-1 frame of a composite signal. 
Available when the Trace format is set to 1 Byte (Refer to 

Traces 

(SONET/SDH)

 on page 284). 

Z0

: Growth. 

SONET: The Z0 byte was used to uniquely identify the STS in 
question. This byte has to be defined in every STS-1 to STS-n frame 
of a composite signal. This byte is only defined for the STS-1 #2 to 
STS-1 #N of a OC-N signal. 

SDH: These bytes are reserved for future international 
standardization. They are located at positions S[1,6N+2] to S[1,7N] 
of an STM-N signal (N > 1). 

B1

: BIP-8 (Bit-Interleaved Parity) byte provides section error 

monitoring. This byte is only defined for the first STS-1/STM-1 frame of a 
composite signal. The byte is calculated by performing a routine 
even-parity check over all bits of the previous STS-N/STM-N frame of a 
composite signal. 

E1

: Orderwire. Provides a 64 Kbit/s voice channel for communication 

between two STEs (Section Terminating Equipment). This byte is only 
defined for the first STS-1/STM-1 frame of a composite signal. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды