EXFO FTB-1 Скачать руководство пользователя страница 352

Страница: 352 / 675

Test Results

340

FTB-700G/800 Series

Alarms/Errors



TIM-V

(Trace Identifier Mismatch - VT) - SONET

LP-TIM

(LOP - Trace Identifier Mismatch) - SDH



SONET: The J2 Trace doesn’t match the expected message value.
Only available when the

TIM-V

check box is selected (refer to

page

Traces (SONET/SDH)

on page 284).



SDH: None of the sampled LP trace strings match the expected
message value. Only available when the

LP-TIM

check box is

selected (refer to page

Traces (SONET/SDH)

on page 284).



PLM-V

(Payload Label Mismatch - VT) - SONET

LP-PLM

(LOP - Payload Label Mismatch) - SDH

: Five consecutive superframes with mismatched VT/LP Signal (bits

5 through 7 of the V5 byte are “000”, “001” or “111”). Only available
when the

PLM-V/UNEQ-V / LP-PLM/LP-UNEQ

check box is selected

(refer to page

Labels

on page 169).



UNEQ-V

(Unequipped - VT) - SONET

LP-UNEQ

(LOP - Unequipped) - SDH

: Bit 5 through 7 of the V5 byte contain “000” for five consecutive

superframes. Only available when the

PLM-V/UNEQ-V /

LP-PLM/LP-UNEQ

check box is selected (refer to page

Labels

page 169).

: Generates samples of unequipped VT/LP signal label (bits 5

through 7 of V5 byte are set to “000”).



ERDI-VSD

(Enhanced RDI - VT Server Defect) - SONET

LP-ERDI-SD

(LOP - Enhanced RDI - Server Defect) - SDH

: Bits 5, 6, and 7 of the Z7 (SONET) / K4 (SDH) byte contain the “101”

pattern, and bit 8 of the V5 byte contain “1”, in five consecutive VT/LP
superframes.

: Generates a “101” pattern for bits 5, 6, and 7 of the Z7 (SONET) / K4

(SDH) byte, and “1” for bit 8 of the V5 byte.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды