manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 488

Test Functions

476

FTB-700G/800 Series

Packet Capture

Frame Length

Specifies the length of the frame that will be saved in the capture buffer.

Complete

 captures the entire frames. 

Truncated

 captures only the first specified number of bytes per frame. 

Use either the Bytes field to manually enter the number of bytes per 
frame or tap on the 

Truncation Calculator

 button for automatic bytes 

per frame calculation. 

Bytes

 allows the selection of the number of bytes that will be saved in 

the capture buffer for each frame captured. Choices are from 14 
(default) to 1536 bytes. 

Truncation Calculator

 allows to easily determine at what byte to 

truncate the frame captured by selecting the desired frame header 
components. 

Header Layer

 specifies the header layer level: 

Layer 2 (Ethernet)

, 

Layer 3 (IP)

, or 

Layer 4 (TCP/UDP)

. 

IP Version

 specifies the IP version: 

IPv4

 or 

IPv6

. 

Encapsulation

 parameters are optional and not selected by 

default. 

VLAN

 check box, when selected, enables VLAN and allows to 

select the number of VLANs: 1, 2, or 3. 

MPLS

 check box, when selected, enables MPLS and allows to 

select the number of labels: 1 or 2. 

Additional Payload (bytes)

 allows to optionally select the number 

of additional payload bytes (1 to 1400 bytes). 

Total Number of Bytes

 indicates the number of bytes for the 

selected frame parameters. This value will be used as the 
truncated frame length (

Truncated

 field). 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды