manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 543

Test Control

NetBlazer

531

Discover Remote Button

Status

 indicates the status of the remote module. 

Loop Up

 and 

Loop Down

 buttons (Not available with RFC 6349 test 

application)

 

Loop Up

 establishes the connection with the selected remote 

module and sets the remote module into 

Smart Loopback

 test 

application. 

If a remote module is in any busy status a user confirmation is 
required to proceed with the Loop Up command.

Following a successful loop up, the IP address of the remote 
module will be used as the destination IP address for the test.

Once the connection is established with the remote module, the 
local module can be set for EtherSAM, RFC 2544, EtherBERT, or 
Traffic Gen & Mon testing. 

Loop Down

 ends the connection between the local and the 

remote modules. 

Status

Description

Idle-

<test application>

a

a.

Possible test applications: EtherSAM, RFC 2544, RFC 6349, EtherBERT,

Traffic Gen & Mon, Smart Loopback, Through Mode, TCP Throughput,

Carrier Ethernet OAM, Cable Test, 1588 PTP, or SyncE. 

The specified test application is selected but not 
running. 

Busy-

<test application>

b

b.

Possible test applications: EtherSAM, RFC 2544, RFC 6349, EtherBERT,

Traffic Gen & Mon, Smart Loopback, TCP Throughput, Carrier Ethernet OAM,

1588 PTP, or SyncE. 

The specified test application is running. 

Not Responding

 

No response from the specified IP address (only 
possible when 

Target

 is set to 

Specific IP

). 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды