manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 343

Test Results

NetBlazer

331

Alarms/Errors

RDI-L

 (Remote Defect Indication - Line) - SONET 

MS-RDI

 (Multiplex Section - Remote Defect Indication) - SDH 

RX

: Bits 6, 7, and 8 of the K2 byte contain the “110” pattern in five 

consecutive frames.

TX

: Generates a “110” pattern for the bits 6, 7 and 8 of the K2 byte. 

Errors

FAS-S

 (Frame Alignment Signal - Section) - SONET 

RS-FAS

 (Regeneration Section - Frame Alignment Signal) - SDH 

RX

: At least one A1 or A2 byte of the FAS word is in error.

B1

 (BIP-8, Bit-Interleave Parity - 8 bits) 

RX

: Indicates a Section (SONET) / Regeneration Section (SDH) parity 

error by performing a routine even-parity check over all frames of the 
previous STS-n/STM-n signal (located in the first STS-1/STM-1 of an 
STS-n/STM-n signal).

B2

 (BIP-8, Bit-Interleave Parity - 8 bits) 

RX

: 

SONET: Indicates a Line parity error by performing an even-parity 
check over all bits of the LOH and SPE of the previous frame 
(located in every STS-1 of an STS-n signal).

SDH: Indicates a Multiplex Section parity error by performing an 
even-parity check over all bits (except those in the RSOH bytes) of 
the previous frame of a STM-N signal.

REI-L

 (Remote Error Indicator - Line) - SONET 

MS-REI

 (Multiplex Section - Remote Error Indicator) - SDH 

RX

: The M0, M1, or the combination of both M0 and M1 bytes indicate 

that one or more BIP violations have been detected. Refer to 

M0 or 

M1/Z2 (SONET)

 on page 491 for more information. For OC-192, also 

refer to 

REI-L Computation Method

 on page 259. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды