EXFO FTB-1 Скачать руководство пользователя страница 207

Страница: 207 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

195

Network Details (iSAM)



Frame Size

The following table lists each component that may affect the
minimum frame size value.

Note:

Sending traffic with frame size > 1518 in switched network may results in
losing theses frames.

Type

Frame Size (bytes)

Fixed

(default)

(default) to 16000

The minimum value is adjusted according to the frame structure and

components selected as shown in the following table.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface.

EMIX

to 16000

Component

Description

C-VLAN

4 bytes

UDP

8 bytes

Ethernet Header

14 bytes

IPv4

20 bytes

Using DTS

4 bytes

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды