manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 544

Test Control

532

FTB-700G/800 Series

Discover Remote Button

Connect

 and 

Disconnect

 buttons are only available with RFC 2544, 

RFC 6349, and EtherSAM test applications.

Connect

 establishes the connection with the selected remote 

module and sets the remote module into either DTS RFC 2544, DTS 
RFC 6349, or DTS EtherSAM test application, depending on the 
active test on the local module. 

If a remote module is in any busy status a user confirmation is 
required to proceed with the Loop Up command. 

Following a successful connection, the IP address of the remote 
module will be used as the destination IP address for the test. 

Disconnect

 ends the connection between the local and the 

remote modules. 

Local Module Identification 

Module ID

 is used to easily identify this module in case another NetBlazer 

is performing a discovery scan. Up to 16 alpha-numeric characters are 
allowed. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды