EXFO FTB-1 Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 675

EXFO FTB-1 Скачать руководство пользователя страница 174

Test Setup - Test Configurator, Timer, and System

162

FTB-700G/800 Series

ISDN PRI - Call Management

ISDN PRI - Call Management

From the

Test

menu, tap

Setup

,

Test Configurator

, the test block, and the

Call Management

tab.

Call Origination Settings



Channel Identification



The channel buttons allow the selection of a channel for call
origination configuration. The selected channel has its button
highlighted with a blue border.

D-Ch

indicates the channel

configured as D-Channel and is not selectable.

A warning icon is displayed on each channel button for which
either the originator and/or destination number is not defined.



Call All at Start

check box when selected, initiates calls for all

configured channels when the test is started.



Calling Party

and

Called Party

defines respectively the originator and

destination call information.



Numbering Plan

choices are

Unknown

,

ISDN/Telephony

(default),

or

Private

.



Numbering Type

choices depend on the

Numbering Plan

and

DS1/E1

Switch Type

selected.

«
...
172
173
174
175
176
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды