manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 182

Test Setup - Test Configurator, Timer, and System

170

FTB-700G/800 Series

Link OAM

Link OAM 

From the test menu, tap

 Setup

, 

Test Configurator

, and the 

Link-OAM (802.3

) test block. 

OAM Mode 

Allows the selection of the OAM mode: 

Active

 (default) initiates the OAM discovery and send OAMPDU 

loopback control; doesn’t respond to variable request nor generate 
Link Event Notification. 

Passive

 doesn’t initiate OAM discovery nor send OAMPDU loopback 

control. 

OAMPDU Destination MAC Address 

Indicates and allows to change the default multicast OAM PDU destination 
MAC address: 

01:80:C2:00:00:02

.

Default

 check box when cleared (default is selected), allows the 

configuration of the OAM PDU destination MAC address: 

00:00:00:00:00:00

 to 

FF:FF:FF:FF:FF:FF

.

Pass/Fail Verdict 

Pass/Fail Verdict

 check box when selected (default) enables the use of the 

pass/fail verdict. A global fail verdict is declared when any of the following 
condition is met: 

Link Down

, any Link OAM alarm, 

Remote Alarms

 (if 

enabled), or 

Remote Loopback

 (if enabled). 

Remote Alarms

 check box when selected (default) considers the 

following alarms to declare the pass/fail verdict: 

Critical Event

, 

Dying 

Gasp

, and 

Link Fault

.

Remote Loopback

 check box when selected (default) considers 

successful/unsuccessful remote loopback request to declare the 
pass/fail verdict. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды