manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 238

Test Setup - Test Configurator, Timer, and System

226

FTB-700G/800 Series

S-OAM and MPLS-TP OAM

Test Function 

Note:

Test Function

 parameters are not configurable when the 

TX Enable

 check 

box is selected. 

Function

 allows the selection of the test function to be performed. 

Loopback

 (default) function is used to verify the bidirectional 

connectivity to a peer MEP (

Continuous

 check box cleared) and to 

verify its capability to sustain close to line rate traffic (diagnostic 
test; 

Continuous

 check box selected). 

Test

 function is used to generate a test signal and/or verify the 

integrity of received test signal from the peer MEP. 

Frame Delay

 function is used to measure the round trip delay with 

the peer MEP. 

Frame Loss

 function is used to measure the frame loss with the 

peer MEP in both directions from a single end point. 

Synthetic Loss

 function is used to measure the frame loss with the 

peer MEP in both directions from a single end point using synthetic 
frames. 

TX Enable

 check box when selected (cleared by default) allows 

transmission of frames. However the transmission will only begin 
when the test is started or if the test is already running. When the 

Continuous

 check box is cleared, the 

TX Enable

 check box is 

automatically cleared once all frames have been transmitted. 

Address Type

, available with S-OAM Mode, defines the destination 

address type of the frame: 

Unicast

 (default) or 

Multicast

. Availability of 

address types depend on selected S

-OAM Mode

 and 

Test Function

. 

Continuous

 check box when selected (default) specifies that the 

frame generation is continuous. The 

Continuous

 check box is cleared 

for Multicast address type. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды