EXFO FTB-1 Скачать руководство пользователя страница 226 | Manualshive

Страница: 226 / 675

EXFO FTB-1 Скачать руководство пользователя страница 226

Test Setup - Test Configurator, Timer, and System

214

FTB-700G/800 Series

RFC 2544 - Subtests



Measurement Mode

, available with

Dual Test Set

for rates from 10M

to 10GE, allows the selection of the latency measurement mode:

Round-Trip

(default) or

One-Way

.

Synchronization with an external 1PPS clock is required to perform
One-Way Latency measurement. One-Way Latency is only possible
when both the local and remote 1PPS signal clocks are valid. The
following alarms are available with One-Way Latency measurement
mode.

LOPPS-L

and

LOPPS-R

(Loss Of Pulse Per Second - Local/Remote) are

declared when either no pulse is received or when no pulse is
received within 1 second ± 6.6

μ

s after the previous pulse. LOPPS-R is

only monitored once the DTS connection is established.



Config. per Frame Size

is available when the

Copy From Throughput

check box is cleared and allows to set the

Max. Rate

for each frame

size. For

Dual Test Set

the

Max. Rate

is configurable for both local to

remote (

L->R

) and remote to local (

R->L

) directions.

All Frames

check box when selected (cleared by default) allows to

enter the maximum rate that will be applied to all frame sizes.

«
...
224
225
226
227
228
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды