EXFO FTB-1 Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 675

EXFO FTB-1 Скачать руководство пользователя страница 146

Test Setup - Test Configurator, Timer, and System

134

FTB-700G/800 Series

EtherBERT, FC BERT, BERT (CPRI), and Unframed BERT

Ethernet Frame

Frame Size (Bytes)

allows to enter the frame size for Ethernet test

applications. The range is from

64

1

to

16000

2

.

The following table lists each component that may affect the minimum
frame size values.

Note:

Sending traffic with frame size >1518 in switched network may result in
losing all frames.

1. The minimum frame size will be adjusted according to the frame structure and components selected.
2. The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical interface.

Component

Description

VLAN

4 bytes per VLAN (up to 3 VLAN)

UDP

8 bytes

TCP 20

bytes

Ethernet Header

14 bytes

LLC and SNAP Headers

8 bytes

IPv4

20 bytes

IPv6 40

bytes

«
...
144
145
146
147
148
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды