manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 514

Test Functions

502

FTB-700G/800 Series

Ping & Trace Route

Ping

Data Size (Bytes)

: Enter the data size that will be sent to the network 

device to be detected. Choices are 

0

 to 

1452 bytes

; 

32 bytes

 by 

default. 

TTL 

for IPv4 and 

Hop Limit (TTL)

 for IPv6: Enter the maximum 

number of hops the packet can go through. Choices are 

1

 to 

255

; 

128

 

by default. 

IP TOS/DS

 for IPv4 and 

Traffic Class (TOS/DS)

 for IPv6: Enter the type 

of service. Choices are 

00

 (default) to 

FF

. 

Flow Label

 (IPv6) value acceptable range is from 

0 

(default) to 

1048575

.

Timeout (ms)

: Enter the maximum time allowed between an ICMP 

echo and response. Choices are 

200 ms

 to 

10000 s

; 

4000 ms

 by 

default. 

Delay (ms)

: Enter the delay between each attempt (PING). Choices 

are 

100

 to 

10000 ms

; 

1000 ms

 by default. 

Attempts: 

Select 

n-Attempts

 to specify the number of ping requests to 

send following a ping activation or select 

Continuous

 to ping 

continuously until manually stopped. If 

n-Attempts

 is selected, enter 

the number of ping attempts from 

1

 to 

100. 

The default setting is 

n-Attempts

 with 

4

 attempts. 

Ping

 button starts the ping tool with the specified settings. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды