manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 532

Test Functions

520

FTB-700G/800 Series

RTD (CPRI Framed L2)

Round Trip Delay 

Indicates the time required for a bit to travel from one point to another. 

Delay T14

 indicates the round trip delay measurement from the Base 

Station going through the Remote Radio Head (including 

Toffset

) and 

back to the Base Station. The 

Delay T14

 appearing on the diagram 

corresponds to the average value. 

Cable Delay

 indicates the cable delay measured from the Base Station 

to the Remote Radio Head (RRH) or vice-versa assuming that the 
cabling in both directions are the same. The 

Cable Delay

 appearing on 

the diagram corresponds to the average value. 

Last

 indicates the result of the last delay measurement.

Minimum

 indicates the minimum delay recorded. 

Maximum

 indicates the maximum delay recorded.

Average

 indicates the average delay value.

Unit

 measurement selections are 

μ

s

 (default) and 

ns

. 

Toffset

 allows the configuration of the internal delay introduced by the 

electronic components in the Radio Equipment (RE): 0 

μ

s (default) to 

66.67 

μ

s. 

Note:

A warning icon appears next to the 

Toffset

 value when this value is larger 

than the 

Delay T14

 value measured indicating that the 

Toffset

 configured 

value maybe invalid thus corrupting the 

Cable Delay

 values reported. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды