EXFO FTB-1 Скачать руководство пользователя страница 540 | Manualshive

Страница: 540 / 675

EXFO FTB-1 Скачать руководство пользователя страница 540

Test Functions

528

FTB-700G/800 Series

Traffic Scan

Monitored Frames Table

Statistics are gathered for each different traffic flow matching the scan
criteria. Each different monitored traffic flow creates a separate entry in the
scan table. When the limit is reached, new traffic flows are not considered
in the table but the existing traffic flows are still monitored.

The level of VLAN (untagged, E-VLAN, S-VLAN, C-VLAN), and values of
VLAN ID, Priority, and TPID are used to identify a traffic flow. Any difference
in one of these values will create a separated entry in the table. PBB-TE
frames are ignored.

Note:

Scan statistics are cleared when restarting the scan.



E-VLAN

/

S-VLAN

/

C-VLAN



ID

indicates the VLAN ID of the received traffic flow.



Priority

indicates the VLAN Priority of the received traffic flow.

Note:

The TPID indicating the Tag Protocol Identifier of the received traffic flow is
reported in the test report.



Statistics



Frame Count

indicates for each traffic flow, the number of frames

matching the selected scan criteria.

Total

indicates the total number of frames matching the selected

scan criteria.



Rate (Mbit/s)

indicates for each traffic flow, the rate of frames

matching the selected scan criteria. The rate is expressed either in

Line Utilization

or

Ethernet Bandwidth

(see

).

Total

indicates the total rate of frames matching the selected scan

criteria.

«
...
538
539
540
541
542
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды