EXFO FTB-1 Скачать руководство пользователя страница 274

Страница: 274 / 675

Test Setup - Test Configurator, Timer, and System

262

FTB-700G/800 Series

Smart Loopback

Smart Loopback

Note:

The Smart Loopback block is only displayed when the

Transparent

(Pseudo-Physical

) check box is cleared (see

Loopback Mode

page 107).

From the

Test

menu, tap

Setup

Test Configurator

, and the Smart

Loopback block.

Loopback



Mode

determines at which layer the Smart Loopback address/port

swapping operation will be.



Ethernet

swaps the MAC addresses of received packets having

their

Destination MAC

address matching the MAC address of the

loopback port.



Ethernet (All Unicast)

swaps the MAC addresses of received

packets having Unicast

Destination MAC

address.



, for Ethernet Layer 3 and 4, swaps the MAC and IP addresses of

received packets having their

Destination IP

address matching the

IP address of the loopback port. For Ethernet Layer 2, swaps the

MAC addresses

for packets having their

Destination MAC

address

matching the MAC address of the loopback port.



UDP/TCP

(default), for Ethernet Layer 4, swaps the UDP or TCP

ports and the MAC and IP addresses of received packets having
their

Destination IP

address matching the IP address of the

loopback port. For Ethernet Layer 3, swaps the MAC and IP
addresses for packets having their

Destination IP

address

matching the IP address of the loopback port. For Ethernet Layer 2,
swaps the

MAC addresses

for packets having their

Destination

MAC

address matching the MAC address of the loopback port.



Matching & Swapping

indicates the Loopback parameters that will be

used based on the Loopback Mode selected.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды