EXFO FTB-1 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 675

EXFO FTB-1 Скачать руководство пользователя страница 54

Test Setup - Test Applications

42

FTB-700G/800 Series

iSAM

iSAM

iSAM is a simplified version of EtherSAM that is centered around addressing
turn-up of E-Line circuits (EVC). The objective of the test is to validate
Carrier Ethernet-based services key performance indicators defined in
MEF: Frame Delay (FD), Inter-Frame Delay Variation (IFDV), and Frame
Loss Ratio (FLR). In addition the RFC 6349 subtest can be enabled to
validate that the Ethernet service is able to properly carry TCP traffic.

The

iSAM

test has to be executed in conjunction with a remote module.

The remote module can be either in loopback configuration for
unidirectional testing or in EtherSAM

Dual Test Set

mode for bidirectional

testing.

The

Dual Test Set

test allows bi-directional test between two compatible

modules providing independent results for each test direction. The results
from local-to-remote and remote-to-local are available on the local testing
unit.



Typical iSAM test applications:



Supported Interfaces/Rates: 10M to 10G LAN/WAN.

Network

under test

(EVC)

Local Unit

Remote Unit

FTB-700G/800 Series

FTB-700G/800 Series

Manual or

Remote

Loopback

Network

under test

(EVC)

Local Unit

Remote Unit

FTB-700G/800 Series

FTB-700G/800 Series

EtherSAM

(DTS)

«
...
52
53
54
55
56
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды