manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 502

Test Functions

490

FTB-700G/800 Series

OH - SONET/SDH

B2

: BIP-8 

SONET: The BIP-8 (Bit-Interleaved Parity) byte provides line error 
monitoring. This byte is only defined for the first STS-1/STM-1 frame of a 
composite signal. The byte is calculated by performing a routine 
even-parity check over all bits of the LOH and the STS-1 frame capacity 
of the previous frame of a composite signal (STS-1 to STS-n). Note that 
the SOH is not used to calculate the parity check. 

SDH: The MS BIP-N*24 (Bit-Interleaved Parity) byte provides line error 
monitoring. The byte is calculated by performing a routine even-parity 
check over all bits of the MSOH and the STM-N frame of the previous 
STM-N frame. Note that the RSOH is not used to calculate the parity 
check. 

K1

 and

 K2

: Automatic Protection Switching (APS): The K1 and K2 bytes 

communicate APS between two LTE. These bytes are only defined for 
the first STS-1/STM-1 frame of a composite signal. 

D4

 through 

D12

: Data Communications Channel (DCC): The D4 

through D12 bytes provide a 576 Kbit/s data communications channel 
between two LTEs for administration, monitoring and other 
communications. These bytes are only defined for the first STS-1/STM-1 
frame of a composite signal. 

S1/Z1 (SONET)

S1

: Synchronization Status: The S1 byte is used to carry the 

synchronization status of the SONET device. This byte is only defined 
for the first STS-1/STM-1 frame of a composite signal. 

Z1

: Growth. This byte is located in the second STS-1 through STS-n 

frame of a composite signal (STS-1 #2, STS-1 #3, up to STS-1 #N of a 
OC-N (N>3) signal). 

S1

 (SDH): Synchronization Status. Bits 5 to 8 of the S1 byte are used to 

carry the synchronization messages of the SDH device. This byte is only 
defined for the first STS-1/STM-1 frame of a composite signal. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды