EXFO FTB-1 Скачать руководство пользователя страница 239

Страница: 239 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

227

S-OAM and MPLS-TP OAM



Requesting MEP ID TLV

(G.8113.1) check box when selected (default)

determines if the Requesting MEP ID TLV is present in the LBM frame.
The

Requesting MEP ID TLV

check box is cleared and not selectable

when the

Continuous

check box is selected.



Priority

, available with S-OAM Mode or when VLAN is enabled (see

VLAN

on page 190), allows to select the VLAN user priority:

(default)

. Refer to

VLAN ID and Priority

on page 639 for more information.



Drop Eligible

, available with S-OAM Mode or when VLAN is enabled

(see

VLAN

on page 190), when set to

Yes

(DEI = 1), the transmitted

frames will be dropped first on receipt when congestion occurs under
test. Drop Eligible is only configurable with

Unicast

address type,

otherwise is set to

(Default). Drop Eligible is set to

for

Frame

Delay

Frame Loss

, and

Synthetic Loss

functions.



Period

determines the transmission period of frames which is set to

100 ms

Period

is not applicable for Multicast address type or when the

Continuous

check box is selected.



TX Rate (%)

is the transmission rate of the LBM frame:

0.0001

95%

for 10M,

99.5%

for 100M,

99.95%

for 1G,

99.995%

for 10G LAN, and

92.8521%

for 10G WAN. Only available with Loopback test function

when the

Continuous

check box is selected.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды