manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 152

Test Setup - Test Configurator, Timer, and System

140

FTB-700G/800 Series

EtherSAM - Global

Global Options

Per Direction Configuration

 check box when selected (default) 

specifies that the values can be configured independently for each 
direction (local to remote and remote to local) for 

Dual Test Set

. 

When the 

Per Direction Configuration

 check box is cleared the 

configuration will be coupled and the values apply to both directions. 

Note:

For 

Dual Test Set

 the 

Per Direction Configuration

 is only available when 

the communication with the remote module is established. 

Pass/Fail Verdict

 check box when selected (default) enables the 

pass/fail verdict. A global pass/fail verdict is given for the EtherSAM test, 

Service Configuration

, and 

Service performance

 (for each service). 

The pass/fail verdict is based on the following criteria: 

Frame Loss

, 

Max Jitter

, 

Round-Trip Latency

, and 

Average RX Rate

. 

Latency Measurement Mode

, available with 

Dual Test Set

 for rates 

from 10M to 10GE, allows the selection of the latency measurement 
mode: 

Round-Trip

 (default) or 

One-Way

.  

Synchronization with an external 1PPS clock is required to perform 
One-Way Latency measurement. One-Way Latency is only possible 
when both local and remote 1PPS signal clocks are valid. The 
following alarms are available with One-Way Latency measurement.

LOPPS-L

 and 

LOPPS-R

 (Loss Of Pulse Per Second - Local/Remote) are 

declared when either no pulse is received or when no pulse is 
received within 1 second ± 6.6 

μ

s after the previous pulse. LOPPS-R is 

only monitored once the DTS connection is established. 

Restore EtherSAM Defaults 

Reverts the current test application to its default factory settings. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды