manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 124

Test Setup - Test Configurator, Timer, and System

112

FTB-700G/800 Series

1588 PTP

1588 PTP 

From the 

Test

 menu, tap

 Setup

, 

Test Configurator

, and the 1588 PTP test 

block. 

PTP

Profile

 is not configurable and is set to 

ITU G.8265.1, 

also called 

Telecom Profile, which is for frequency synchronization. 

Mode

 is not configurable and is set to 

Unicast

 which implies a 

dedicated communication link between the master and the slave 
clock. 

Framing

 is not selectable and is set to 

UDP/IPv4

. 

Domain

 is the PTP domain parameter used by the 1588 PTP function to 

communicate with the Grand Master clock: 

4

(default) to 

23

. 

GM IP Address

 is the IP address of the Grand Master Clock used by the 

1588 PTP function to communicate with it. 

Quick Ping

 button allows to test if the Grand Master IP address can be 

reached. A message is returned indicating if the ping attempt was 

Successful

 or 

Failed

. 

IP

 

TOS/DS

 allows to enter the Type of Service: 

0x00

(default) to

0xFF

. 

Mechanism

 is not selectable and is set to 

Delay Req-Resp

 (Delay 

Request-Response) which specifies the mechanism used by the 
1588 PTP function to communicate with the Grand Master clock. Refer 
to 

Delay Request-Response

 on page 596 for more information. 

Delay Mode

 is not selectable and is set to 

Two-way

 which uses 

Sync/Follow Up, Delay Request, and Delay Response messages. 

Connect

 button is used to initiate the Grand Master Connection 

process. This process is also automatically initiated when starting the 
test if not already initiated. The process automatically ends when 
stopping the test. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды