manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 219

Test Setup - Test Configurator, Timer, and System

NetBlazer

207

RFC 2544 - Global

Subtests and Estimated Time 

Subtests

 allows to individually enable the 

Throughput

, 

Back-to-Back

, 

Frame Loss

, and 

Latency

 subtests. 

Estimated Time (H:MM) 

indicates the estimated time required to 

complete each subtest at best conditions. The total estimated time to 
complete all subtests is also displayed. 

Frame Distribution 

Frame Distribution

 allows to select either 

RFC 2544

 (default) or 

User 

Defined

 distribution. 

Quantity

 is only available when 

User Defined

 is selected and allows to 

select the number of frames, from 

1 

to 

10

 (

7

 by default), in the 

distribution. 

Frame Size (Bytes):

 For 

RFC 2544

 distribution, gives predefined frame 

size distribution values. For 

User Defined

 distribution, enter up to 

seven frame size values. 

Distribution

Frame Size

RFC 2544

64

a

,

128

, 

256

, 

512

, 

1024

, 

1280

, and 

1518

a.

The minimum frame size will be adjusted according to the frame structure and

components selected.

User Defined

64

a

 to 

16000

b

b.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды