manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 216

Test Setup - Test Configurator, Timer, and System

204

FTB-700G/800 Series

Remote Details (iSAM)

For Remote Loopback Operation Mode 

Loop-Up

 button establishes the connection with the selected remote 

module and sets the remote module into 

Smart Loopback

 test 

application. 

Following a successful loop-up, the IP address of the remote module 
will be used as the destination IP address for the test.

Overtake

 button manually establishes the connection with the remote 

module and set the remote module into Smart Loopback test 
application. Available when the status is 

Taken

 or 

Test in Progress

 

with another unit. A confirmation is required to overtake a module. 

Loop-Down

 button ends the connection between the local and the 

remote modules. 

For DTS Operation Mode 

Connect

 button manually establishes the connection with the selected 

remote module and sets the remote module into DTS EtherSAM test 
application. 

Following a successful connection, the IP address of the remote 
module will be used as the destination IP address for the test.

Overtake

 button manually establishes the connection with the remote 

module and set the remote module into DTS EtherSAM test application. 
Available when the status is 

Taken

 or 

Test in Progress

 with another 

unit. A confirmation is required to overtake a module. 

Following a successful connection, the IP address of the remote 
module will be used as the destination IP address for the test.

Disconnect

 button, available once the connection with the remote 

module is established, terminates the connection with the remote 
module. Available when the status is 

Ready

.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды