EXFO FTB-1 Скачать руководство пользователя страница 179

Страница: 179 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

167

ISDN PRI - ISDN Settings

ISDN PRI - ISDN Settings

From the

Test

menu, tap

Setup

Test Configurator

, the test block, and the

ISDN Settings

tab.

D-Channel



Channel

indicates the channel selected to establish the ISDN signalling

path. The default D-Channel for DS1 is

and for E1 is



Rate

represents the rate at which data is exchanged. Depending on the

network, the options available are

56K

and

64K

(default).



HDLC Mode

represents the bit inversion of the signal:

Normal

(default) or

Inverted



D-Channel

indicates the status of the D-Channel. A green arrow

pointing up indicates that the link is up (

L2 - Multiple frame

established

) and a red arrow pointing down indicates that the link is

down.

B-Channel

Note:

The following B-Channel settings apply to all data calls.



Data Call Pattern

allows to select the pattern:

PRBS9

PRBS11

(default),

PRBS20

1111

1100

1010

0000

1in8

1in16

2in 8

and

3in24



Invert

check box when selected (cleared by default) inverts the test

pattern meaning that every 0 will be changed for 1 and every 1 for 0.
For example, the pattern 1100 will be sent as 0011.



RX Pattern Analysis

check box when selected enables the monitoring

of the test pattern for all data calls.



BER Pass/Fail Verdict

allows to enable bit error pass/fail verdict by

selecting either

Bit Error Count

Bit Error Rate

(default) or

Disabled

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды