EXFO FTB-1 Скачать руководство пользователя страница 199

Страница: 199 / 675

Test Setup - Test Configurator, Timer, and System

NetBlazer

187

Network

For

IPv6

the following configuration parameters are displayed:

Link-Local

IPv6 Address

Global IPv6 Address

, and

Default Gateway

. Tap on the

Config

button to access all settings.



Link-Local IPv6 Address

(LLA) is used for local communication

between on-link neighbors and for Neighbor Discovery process.



Mode

Stateless Auto

(default) allows automatic generation of the IPv6

address based on the MAC address.

Static

allows to enter the IP Address.



Address

, available with

Static

mode, allows to select the

Link-Local IPv6 Address. The accepted range is from

FE80:0000:0000:0000:0000:0000:0000:0000

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF.

The default address

FE80::[Interface ID]

, where [

Interface ID

] is generated from

the source MAC address. When the

Address

field is selected for

editing using virtual keyboard, the

Previous IPs

button appears

allowing to select a previously configured IP address.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды

EXFO FTB-1, Руководство пользователя

Результаты поиска

Содержание FTB-1

Отзывы:

Бренды по названию

Популярные бренды