manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 193

Test Setup - Test Configurator, Timer, and System

NetBlazer

181

MAC/IP/UDP

The following configuration parameters are available for both 

IPv4

 and 

IPv6

 unless otherwise specified. 

Quick Ping

 button automatically starts the quick Ping utility for the 

stream destination IP address and provides either a successful or failed 
result. The quick Ping uses 3 attempts, a Delay of 1 second, a Timeout 
of 2 seconds, and a Data Size of 32 Bytes. Refer to 

Ping & Trace Route

 

on page 501 for more options. 

Resolve MAC Address

 check box, when selected (default), sends a 

request to the network to retrieve the MAC address corresponding to 
the selected destination IP address. This setting is coupled with the 
Resolve MAC Address check box from 

MAC

 on page 175. The Resolve 

MAC address status is displayed. Possible status are: 

Source IP Multiplicator

 check box, when selected (cleared by 

default), allows changing the 7 LSB (Least Significant bit) of the source 
IP address as specified in the range: 

1-128

 (default) or 

0-127

. 

Subnet Mask

 (IPv4) allows to enter the Subnet Mask for the stream. 

The default setting is 

255.255.0.0

. Not available when the 

Automatic IP 

(DHCP)

 check box is selected. 

Default Gateway

 (IPv4) check box, when selected (cleared by 

default), allows to enter a default Gateway IP address. When the 

Default Gateway

 check box is selected, its default address is 

0.0.0.0

. 

The 

Default Gateway

 address is not configurable when the 

Automatic 

IP (DHCP)

 check box is selected. 

Status

Description

--

The 

Resolve MAC address

 is not enabled.

Resolving

The MAC address is being resolved.

Resolved

The MAC address is resolved.

Failed

The MAC address cannot be resolved.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды