EXFO FTB-1 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 675

EXFO FTB-1 Скачать руководство пользователя страница 68

Test Setup - Test Applications

56

FTB-700G/800 Series

RFC 2544

RFC 2544

RFC 2544 allows Ethernet Throughput, Back-to-Back, Frame Loss, and
Latency performance testing in accordance with RFC 2544 specifications.

The

RFC 2544

test has to be executed in conjunction with a remote

module. The remote module can be either in loopback configuration for
unidirectional testing or in RFC 2544

Dual Test Set

mode for bidirectional

testing.

The

Dual Test Set

test allows bi-directional test between two compatible

modules providing independent results for each test direction. The results
from local-to-remote and remote-to-local are available on the local testing
unit.



Typical RFC 2544 testapplications:



Supported Interfaces/Rates: 10M to 10G LAN/WAN.

Network

under test

Testing Unit

Loopback Unit

FTB-700G/800 Series

FTB-700G/800 Series

Network

under test

Testing Unit

Remote Unit

FTB-700G/800 Series

FTB-700G/800 Series

«
...
66
67
68
69
70
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды