manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 247

Test Setup - Test Configurator, Timer, and System

NetBlazer

235

Services - Profile

Note:

The 

CIR

 value will be calculated on the basis of the selected service profile 

and the value entered in the 

Number of Calls

 or 

Number of Channels

 

field.

Frame Size (Bytes)

 indicates the frame size for 

Voice

 and 

Video

 

profiles and allows to change the frame size for 

Data

 profile: 

Fixed

(default) 

Profile and 

Codec

Type

Frame Size (bytes)

IPv4

IPv6

Voice Codec:
- VoIP G.711
- VoIP G.723.1
- VoIP G.729

Fixed

138

82
78

158
102

98

Video Codec: All

Fixed

1374

1394

Data

Fixed

 (default)

64

a

 (default) to 16000

b

a.

The minimum value is adjusted according to the frame structure and components

selected as shown in the following table. 

b.

The maximum frame size is limited to 10000 for 10/100/1000Mbps electrical

interface. 

Random

64

a

 to 1518

c

c.

The maximum frame size value is adjusted for each enabled VLAN (+4 bytes per

VLAN). 

EMIX

64

a

 to 16000

b

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды