manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 190

Test Setup - Test Configurator, Timer, and System

178

FTB-700G/800 Series

MAC/IP/UDP

IP 

For 

IPv4

 the following configuration parameters are available. 

Automatic IP (DHCP)

 check box, when selected (cleared by default), 

allows to dynamically obtain an IP address from a DHCP (Dynamic 
Host Configuration Protocol) server. 

Source IP Address

 allows to enter the source IP address for the 

stream. The default setting is 10.10.x.y, where x and y are respectively 
the two least significant bytes of the port default MAC address. Not 
available when the 

Automatic IP (DHCP)

 check box is selected. 

Destination IP Address

 allows to enter the destination IP address for 

the stream. The default setting is the source IP address. 

For 

IPv6

 the following configuration parameters are displayed: 

Source 

Link-Local IPv6 Address

, and 

Source Global IPv6 Address

. Tap on the 

IPv6 Config

 button to access all settings. 

Link-Local IPv6 Address

 (LLA) is used for local communication 

between on-link neighbors and for Neighbor Discovery process. 

Mode

Stateless Auto

 (default) allows automatic generation of the IPv6 

address based on the MAC address. 

Static

 allows to enter the IP Address. 

Address

, available with 

Static

 mode, allows to select the 

Link-Local IPv6 Address. The accepted range is from 

FE80:0000:0000:0000:0000:0000:0000:0000

 to 

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF.

 The default address 

is

 FE80::[Interface ID]

, where [

Interface ID

] is generated from 

the source MAC address. When the 

Address

 field is selected for 

editing using virtual keyboard, the 

Previous IPs

 button appears 

allowing to select a previously configured IP address. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды