EXFO FTB-1 Скачать руководство пользователя страница 185 | Manualshive

Страница: 185 / 675

EXFO FTB-1 Скачать руководство пользователя страница 185

Test Setup - Test Configurator, Timer, and System

NetBlazer

173

MAC/IP/UDP

Modify Frame Structure

Allows to modify the structure of the frame.



Global Option

is only available with EtherSAM and Traffic Gen & Mon

test applications.



S-OAM

check box when selected, enables EtherSAM over service

OAM at Layer 2 on all services. The EtherSAM uses LBM and LBR
messages of the S-OAM protocol to perform the test. A device
having the capability to loopback LBM messages (via LBR) is
required at the remote. Only available with EtherSAM. Not available
in Dual Test Set.



Layer Mode

sets the frame layer mode for all services (available

with EtherSAM when the S-OAM check box is cleared):

Mixed

(default) allows configuring the frame layer per service: L2,

L3, or L4.

L2 Only

configures all services to Layer 2 only (no IP, no MPLS).



IP Version

allows to select

IPv4

(default) or

IPv6

that will be used

for both the interface and streams/services.



Framing



Frame Format

(layer 2) allows to select

Ethernet II

(default) or

802.3 SNAP

as the frame format.



Network Layer

1

,

2

(layer 3) sets the network traffic type:

IPv4

(default)/

IPv6

, or

None

.

1. Not available with EtherSAM when the

S-OAM

check box selected.

2. Not configurable and set to

None

when

Layer Mode

is set to

L2 Only

.

«
...
183
184
185
186
187
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды