Avaya DEFINITY Server R Скачать руководство пользователя страница 92

Страница: 92 / 550

Upgrading G3rV4 and R5/6/7/8r to Avaya DEFINITY
Server R running Avaya Communication Manager

555-233-115

2-44

Issue 7 November 2003

For high or critical reliability:

1. Type busyout host-adapter a and press

Enter.

Make sure it says PASS.

2. Check the label on the TN1657 disk drive. If it is Vintage 9 or later, lock it in

place.

3. If the TN1657 disk drive is Vintage 8 or earlier, remove it and place it in

antistatic packing material.

4. Insert the new TN1657 disk drive, V9 or later, all the way into the slot and

lock in place.

5. Type reset host-adapter a and press

Enter

to release the disk from the

maintenance-busyout condition and put it back into service.

6. Type release host-adapter a and press

Enter

to allow the disk to spin up

Wait until all LEDs go out, about 2 minutes.

7. Type status spe and press

Enter

to verify that the disk is present and in

service.

NOTE:

If the disk drive fails to return to service, repeat the steps.

8. Type list configuration control and press

Enter

to verify the disk drive

vintages. If the field shows V0000 for the vintage, unlock and back out the
disk drives and repeat the steps 1 through 5.

Repeat for the SPE B:

9. Type busyout host-adapter b and press

Enter.

Make sure it says PASS.

10. Check the label on the TN1657 disk drive. If it is Vintage 9 or later, lock it in

place.

11. If the TN1657 disk drive is Vintage 8 or earlier, remove it and place it in

antistatic packing material.

12. Insert the new TN1657 disk drive, V9 or later, all the way into the slot and

lock in place.

13. Type reset host-adapter b and press

Enter

to release the disk from the

maintenance-busyout condition and put it back into service.

14. Type release host-adapter b and press

Enter

to allow the disk to spin up

Wait until all LEDs go out, about 2 minutes.

15. Type status spe and press

Enter

to verify that the disk is present and in

service.

NOTE:

If the disk drive fails to return to service, repeat the steps.

16. Type list configuration control and press

Enter

to verify the disk drive

vintages. If the field shows V0000 for the vintage, unlock and back out the
disk drives and repeat the steps 7 through 11.

Содержание DEFINITY Server R







































































































































































































































































































































































































































































































































































Результаты поиска

Содержание DEFINITY Server R

Отзывы:

Похожие инструкции для DEFINITY Server R

Бренды по названию

Популярные бренды

Avaya DEFINITY Server R, Руководство пользователя

Результаты поиска

Содержание DEFINITY Server R

Отзывы:

Похожие инструкции для DEFINITY Server R

Бренды по названию

Популярные бренды