Avaya DEFINITY Server R Скачать руководство пользователя страница 210 | Manualshive

Страница: 210 / 550

background image

Upgrading a Multicarrier G2 Universal Module to Avaya
DEFINITY Server R EPN running Avaya Communication
Manager

555-233-115

5-20

Issue 7 November 2003

■

Four spare carrier ground straps

■

Wrist ground strap

■

Repair kit for backplane pins (KS-22876 L2 or equivalent)

Follow Routine Preventive Maintenance

During the upgrade, follow routine preventive maintenance procedures on the
system to be upgraded. For information about the procedures and necessary
equipment, refer to the “Preventive Maintenance” section in Maintenance for
Avaya DEFINITY Server R.

Label Cables

To make reconnecting the cables simpler and more reliable, label both ends of the
connector cables associated with the carrier to be removed.

Remove Module Control Carrier(s)

Check Link Status

1. Type display communication-interface links and press

Enter

. Write down

all enabled links.

2. Type status link number and press

Enter

. Repeat this step for all links.

3. Write down which links are in service.

Power Down G2 System

1. At the common control’s power distribution unit, set the main circuit breaker

to OFF.

2. At the universal module’s power distribution unit, set the main circuit

breaker to OFF.

Install Power-Failure Transfer Ground Wire

!

CAUTION:

To avoid contaminating single-point ground, do not connect the ground wire
while the system is powered up.

1. Connect a 10 AWG (#25) (2.6 mm

2

) wire to pin 49 of the connecting block

or to pin 49 of the CAP (cable access panel) on the power-failure transfer
panel.

2. Route the opposite end of the wire to an approved ground and connect.

«
...
208
209
210
211
212
...
»

Содержание DEFINITY Server R







































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DEFINITY Server R

S1V30080 Series

Бренд: Seiko Epson Страницы: 10

Бренд: NXP Semiconductors Страницы: 269

Бренд: ASROCK Страницы: 83

Бренд: IBASE Technology Страницы: 60

Бренд: AMD Geode Страницы: 51

Бренд: BCM Страницы: 93

Бренд: Gigabyte Страницы: 37

Бренд: MSI Страницы: 85

Бренд: ASROCK Страницы: 18

Бренд: Intel Страницы: 30

Бренд: Intel Страницы: 62

AIMB-742 Socket 478

Бренд: Intel Страницы: 4

Бренд: Gigabyte Страницы: 104

Бренд: OLIMEX Страницы: 14

BLKD955XBKLKR - 10PK 955X LGA775 8GB DDR2 16X

Бренд: Intel Страницы: 94

Z68A-G43 G3 Series

Бренд: MSI Страницы: 152

Бренд: Diodes Страницы: 7

Бренд: TYAN Страницы: 117

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды