97
* After correcting the condition, cycle the key switch On-Off-
On
Code
Fault Description
Fault Condition
Possible Cause
EPS Fault Recovery Method
C1301 Over Current
EPS internal over-current condition has
been detected
Internal EPS Condition
Correct EPS condition*
C1302 Excessive Current Error EPS internal current measurement error
has been detected
Internal EPS Condition
Correct EPS condition*
C1303 Torque Sensor Range
Fault
EPS internal torque sensor range
condition has been detected
Internal EPS Condition
Correct EPS condition*
C1304 Torque Sensor Linearity
Fault
EPS internal torque sensor linearity
condition has been detected
Internal EPS Condition
Correct EPS condition*
C1305 Rotor Position Encoder EPS internal rotor position encoder
condition has been detected
Internal EPS Condition
Correct EPS condition*
C1306 System Voltage Low
EPS battery power low-voltage
condition has been detected
System voltage low (less than 11 VDC at the
EPS). Wire harness issue, faulty voltage
regulator, weak battery or loose battery
terminals.
EPS will auto-recover when the
battery supply returns to normal
C1307 System Voltage High
EPS battery power over-voltage
condition has been detected
System voltage high (more than 16 VDC at the
EPS). Wire harness issue, faulty voltage
regulator or loose battery terminals.
EPS will auto-recover when the
battery supply returns to normal
C1308 Temperature Above 110°
C
EPS internal 110o C over-temp
condition has been detected
Clean the EPS housing and cooling fins.
EPS will auto-recover when internal
temperature drops below 105° C
C1309 Temperature Above 120°
C
EPS internal 120o C over-temp
condition has been detected
Clean the EPS housing and cooling fins.
EPS will auto-recover when internal
temperature drops below 115° C
C1310 Vehicle Speed High
Vehicle speed signal received by the
EPS exceeds the maximum speed
specification
Intermittent main harness wires, defective
speed-sensor, or intermittent speed sensor
wires.
EPS will auto-recover when the
vehicle speed signal drops below the
maximum speed specification
C1311 Vehicle Speed Low
Vehicle speed signal received by the
EPS is zero or missing
Broken main harness wires, defective speed-
sensor, or broken speed sensor wires.
EPS will auto-recover when the
vehicle speed signal returns to normal
C1312 Vehicle Speed Faulty
Vehicle speed CAN signal received by
the EPS incorrect or missing
Broken main harness CAN wires, defective
speed-sensor, or broken speed sensor wires.
EPS will auto-recover when the
vehicle speed signal returns to normal
C1313 Engine RPM High
Engine RPM signal received by the EPS
exceeds the maximum RPM
specification
Intermittent main harness RPM wires,
intermittent voltage regulator, intermittent ACG
stator wires.
EPS will auto-recover when engine
RPM signal drops below the
maximum RPM specification
C1314 Engine RPM Low
Engine RPM signal received by the EPS
suddenly dropped below 500 RPM
Handlebar switch in the "OFF" position, broken
main harness RPM wires, defect voltage
regulator, broken ACG stator wires.
EPS will auto-recover when engine
RPM signal returns to normal
C1315 Engine RPM Faulty
Engine RPM CAN signal received by the
EPS incorrect or missing
Broken main harness CAN wires or defective
ECM.
EPS will auto-recover when engine
RPM signal returns to normal
C1316 EEPROM Error
EPS internal memory error has been
detected
Internal EPS condition
Correct EPS condition*
C1317 CAN Bus Error
The EPS has lost CAN communication
with the EFI ECM
Broken CAN wires in the main harness. EFI
ECM connector has been disconnected.
Correct EPS condition*
C1318 Internal CRC Error
EPS internal CRC calculation condition
has been detected
EPS reflash has failed. Battery power was lost,
or the key switch was turned off, during EPS
reflash programming.
EPS must be reprogrammed
C1319 Boot Counter Exceeded EPS internal application code condition
has been detected
Intermittent power has prevented a successful
application code launch.
Correct EPS power condition*
C1320 Incorrect Vehicle Speed-
to-RPM Ratio
Vehicle speed signal received by the
EPS exceeds 10 MPH, but the engine
RPM signal less than 500 RPM
Intermittent or broken main harness RPM wires,
intermittent voltage regulator, intermittent or
broken ACG stator wires.
Correct EPS condition*
C1321 Vehicle Speed Erratic
Vehicle speed signal received by the
EPS changing at an unrealistic rate
Intermittent main harness, intermittent speed
sensor, dirty speed senor or trigger wheel.
Correct EPS vehicle speed signal
condition*
C1322 Engine RPM Lost
Engine RPM signal received by the EPS
exceeds 500 RPM and then is zero or
missing
Handlebar switch in the "OFF" position, broken
main harness RPM wires, defect voltage
regulator, broken ACG stator wires.
EPS will auto-recover when engine
RPM signal returns to normal
C1323 "EPS OFF" Gauge
Display
Battery power has been applied to the
EPS for more than 5-minutes, but no
engine RPM signal has been detected
The EPS has been automatically disabled, after
5-minutes of inactivity, to conserve battery
power.
EPS will auto-recover when engine is
started or the keyswitch is cycled On-
Off-On
C1324 Loss of CAN
communication with
EPS unit
The gauge has lost CAN communication
with the EPS
Broken CAN wires in the main harness or
disconnected EPS. This is not an EPS
generated DTC; gauge DTC display only.
Gauge DTC display will clear when
the EPS-to-gauge CAN
communication is restored.
C1325 Dual Loss
EPS loss of both the vehicle speed and
the engine RPM signals has been
detected
Handlebar switch in the "OFF" position, the
engine stalled (key switch "ON"), broken
harness wires, loss of CAN data signal.
EPS will auto-recover when either the
vehicle speed or engine RPM signal
is restored.
C1326 Rotor Position Encoder EPS internal rotor position encoder
variance condition has been detected
Internal EPS Condition
Correct EPS condition*
C1327 Voltage Converter Error
(Low)
EPS internal voltage converter low-
voltage condition has been detected
Internal EPS Condition
Correct EPS condition*
C1328 Voltage Converter Error
(High)
EPS internal voltage converter over-
voltage condition has been detected
Internal EPS Condition
Correct EPS condition*
C1329 Internal Data Error
EPS internal preloaded data condition
has been detected
Internal EPS Condition
EPS must be reprogrammed
Содержание HDX CREW 2017
Страница 1: ...2017 S SERVICE ERVICE MANUAL ANUAL www arcticcat com...
Страница 151: ...150 NOTES...