Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 144 / 152

143

HDX087A

Shock Absorber
REMOVING

1. Secure the vehicle on a support stand to elevate the

wheels and to release load on the suspension.

2. Remove the two cap screws and nuts securing each

front shock absorber to the frame and upper A-arm.

PR911

3. Remove the two cap screws and nuts securing each

rear shock absorber to the frame and lower A-arm.

Account for four spacers and O-rings from each.

HDX294

4. Using a suitable shock spring compressor, compress

the shock absorber spring, remove the spring

retainer, and remove the spring.

HDX336

CLEANING AND INSPECTING

1. Clean all shock absorber components in parts-clean-

ing solvent.

2. Inspect each shock rod for nicks, pits, rust, bends,

and oily residue.

3. Inspect all springs, spring retainers, shock rods,

sleeves, bushings, shock bodies, and eyelets for

cracks, leaks, and bends.

INSTALLING

1. Place the shock absorber spring over the shock

absorber, compress the spring, and install the

retainer.

2. Place bushings and sleeves (where appropriate) into

shock eyelet; then install shocks with two cap screws

and nuts.

3. Tighten the shock absorber cap screws to 35 ft-lb.

4. Remove the vehicle from the support stand.

Rear Shock Absorber Spring
REMOVING

1. Using soft jaws or a shop towel, secure the bottom

shock assembly eyelet into a vise; then, using readily

available shock spring compressors, install the spring

compressors onto the spring towards the bottom end

of the assembly.

! WARNING

Make sure the vehicle is solidly supported on the sup-
port stand to avoid injury.

CAUTION

Additional support stands are necessary to support the
rear axle when the shock absorbers are removed or
damage may occur.

Front

Rear

! WARNING

Shock absorber springs are under high compression
loads. Do not attempt to remove springs without an ade-
quate spring compressor. Sever injury could result.

Front

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды