Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 113

Страница: 113 / 152

112

TPS (TPS)

WT539

Display: TPS position (0% closed, 95-100% WOT).

DTC: P0121, P0122, P0123

Usage: Verify TPS signal and adjust throttle cable.

Fuel Sensor (FUEL)

WT545

Display: Fuel level signal from the fuel level sensor.

DTC: C1400, C1401, C1402

Usage: Check output of the fuel level sensor.*

1. Full fuel is indicated by a reading of 0-5 ohms.

2. Empty is indicated by a reading of 95-105 ohms.

* 110-500 ohms, suspect the fuel level sensor or wiring. 0-100 ohms but

no gauge indication, suspect the gauge.

Tachometer (RPM)

WT544

Display: Engine RPM

DTC: P0336, P0337, P0339

Usage: Verify engine speed signal from the following.

1. CKP (crankshaft position) sensor to ECM

2. ECM (CAN) signal to gauge (tachometer)

3. ECM (CAN) signal to EPS

Speedometer (SPEED)

WT543

Display: Vehicle speed signal.

DTC: P0500

Usage: Verify speedometer sensor signal from the fol-

lowing.

1. Speed sensor to ECM.

2. ECM (CAN) signal to gauge (speedometer/odometer).

3. ECM (CAN) signal to EPS

DIAGNOSTIC TROUBLE CODES (DTC)

If an EFI or related chassis component fails or an out-of-

tolerance signal is detected by the ECM, a diagnostic

trouble code (DTC) will be generated in the ECM and

displayed on the LCD. The DTC will be displayed alter-

nately with a wrench icon or malfunction indicator light

(MIL). The DTC will continue to flash, until the mal-

function is corrected and the code cleared.

Code List



NOTE: Each of the following numerical codes will

have a one-letter prefix of C, P, or U. A “C” prefix

denotes a chassis malfunction, a “P” prefix denotes a

power train malfunction, and a “U” prefix denotes a

loss of communication with the gauge.



NOTE: Normal malfunction codes are cleared from

the LCD when the component is replaced or the mal-

function is corrected; however, intermittent codes

must be cleared as noted in the code chart.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды