Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 57 / 152

Inspecting Cylinder

1. Using a slide gauge and a dial indicator or a snap

gauge, measure the cylinder bore diameter in three

locations from top to bottom and again from top to

bottom at 90° from the first measurements for a total

of six measurements. The trueness (out-of-round-

ness) is the difference between the highest and low-

est reading. Maximum trueness (out-of-roundness)

must not exceed specifications.

CC127D

2. Wash the cylinder in parts-cleaning solvent.

3. Inspect the cylinder for pitting, scoring, scuffing, and

corrosion. If marks are found, repair the surface

using a #320 grit ball hone.



NOTE: To produce the proper 60° cross-hatch pat-

tern, use a low RPM drill (600 RPM) at the rate of 30

strokes per minute. If honing oil is not available, use a

lightweight petroleum-based oil. Thoroughly clean

cylinder after honing using soap and hot water. Dry

with compressed air; then immediately apply oil to

the cylinder bore. If the bore is severely damaged or

gouged, replace the cylinder.

H1-038

4. If any measurement exceeds the limit, replace the

cylinder and piston.

Measuring Camshaft Runout



NOTE: If the camshaft is out of tolerance, it must be

replaced.

1. Place the camshaft on a set of V blocks; then position

the dial indicator contact point against the shaft and

zero the indicator.

CC283D

2. Rotate the camshaft and note runout; maximum

runout must not exceed specifications.

Measuring Camshaft Lobe Height

1. Using a calipers, measure each cam lobe height.

ATV1013A

2. The lobe heights must be greater than minimum

specifications.

Inspecting Camshaft Bearing Journal

1. Inspect the bearing journal for scoring, seizure

marks, or pitting.

2. If excessive scoring, seizure marks, or pitting is



NOTE: If the journals are worn, replace the cam-

shaft.

Inspecting Camshaft Spring/Drive Pin

1. Inspect the spring and drive pin for damage.

CF061A

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды