Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 111 / 152

110



NOTE: If a “click” is heard and more than one volt

is indicated by the multimeter, replace the starter

relay. If no “click” is heard and the multimeter con-

tinues to indicate battery voltage, proceed to step 4.

4. Disconnect the two-wire plug from the starter relay;

then connect the red tester lead to the green wire and

the black tester lead to the black wire.

HDX281B

5. Depress the starter button and observe the multimeter.



NOTE: If battery voltage is indicated, replace the

starter relay.



NOTE: If it is determined that the positive battery

cable is faulty and needs replacement, verify the rout-

ing and cable tie locations when installing a new cable

(see Battery section).

Electronic Control Module

(ECM)

The ECM is located beneath the front seat near the bat-

tery.



NOTE: The ECM is not a serviceable component. If

the unit is defective, it must be replaced.

The ECM is rarely the cause for electrical problems;

however, if the ECM is suspected, substitute another

ECM to verify the suspected one is defective.

This EFI system has a built-in feature that will only allow

an ECM of the same part number to be used in this

model. Do not attempt to substitute an ECM from a dif-

ferent model as the system will not allow it to start.

Error codes can be cleared by following the procedures

located in the EFI Diagnostic System sub-section in this

section.



NOTE: If the throttle body, ECM, TPS, or ISC are

replaced, the EFI system must be synchronized. Use

the following procedure.

1. With the key off, depress accelerator pedal to Wide

Open Throttle (WOT).

2. Place the ignition key in the ON position and wait for

10 seconds.

3. Release the accelerator pedal, and wait an additional

10 seconds.

4. Turn the key to the OFF position and allow the gauge

to shut off.

EFI Diagnostic System

DIGITAL GAUGE

The digital gauge can be used as a diagnostic tool for

many of the DTC’s displayed. To place the gauge into the

diagnostic mode, use the following procedure.

1. Turn the ignition switch ON.

2. Depress and hold both left and right buttons together

for approximately three seconds until “DIAGNOS-

TIC” appears on the LCD.

WT541

3. Press the center button (SELECT) to enter diagnostic

mode; cycle the display by pressing either the left or

right button to step to the desired function.



NOTE: The gauge can be utilized dynamically

(engine running/vehicle moving) or statically (engine/

vehicle stopped).

DIAGNOSTIC MODES
Battery (BATTERY)

WT540

Display: System DC voltage.

DTC: P0562, P0563, P2531, P2532

Usage: Verify system voltage under following condi-

tions.

1. Battery voltage with engine and accessories off

(>12.2 VDC for fully charged).

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды