Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 14

Страница: 14 / 152

PR920

Move the shift lever all the way back. The letter L should

illuminate on the LCD gauge.

PR921

If either park or low range cannot be reached, the shift

cable must be adjusted.

ADJUSTING SHIFT CABLE

1. Place the transmission in park; then tilt the cargo

box.

2. Make sure the shift lever is in park; then remove the

E-clip securing the cable end to the shift arm stud.

HDX251

3. Loosen nuts (A) and (B) and adjust the cable housing

to align the shift cable end to the shift arm stud.

HDX261B

4. Install the E-clip; then tighten the nuts (A) and (B) to

8 ft-lb.

5. Check each gear shift position for proper gear selection

and make sure the proper icon illuminates on the LCD.

Hydraulic Brake System



NOTE: This ROV is equipped with hydraulic

brakes at all four wheels.

CHECKING/BLEEDING

The hydraulic brake system has been filled and bled at

the factory.

1. With the master cylinder in a level position, check

the fluid level in the reservoir. If the level in the res-

ervoir is not above the MIN, add DOT 4 brake fluid.

PR095

2. Depress the brake pedal several times to check for a

firm brake. If the brake is not firm, the system must

be bled. To bleed the brake system, use the following

procedure.

A. Remove the cover and fill the reservoir with DOT 4

brake fluid; then install and secure the cover.

B. Slowly depress the brake pedal several times.

C. Install one end of a clear hose onto the RIGHT

REAR bleeder screw and direct the other end into a

container; then while holding slight pressure on the

brake pedal, open the bleeder screw and watch for air

bubbles. Close the bleeder screw before releasing the

brake pedal. Repeat this procedure until no air bub-

bles are present.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды