Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 132 / 152

131

HDX392



NOTE: Steps 1-3 can be used to replace the out-

board boot.

ASSEMBLING AXLES

1. Install the inner boot with the small clamp making

sure the ends of the clamp are positioned correctly.



NOTE: Position the end of the clamp opposite the

forward rotation of the axle.

HDX393A



NOTE: The boot is positioned correctly when the

small end of the boot seats down into the recessed

groove.

2. Using the boot clamp tool, secure the small clamp of

the inner boot.

ATV-1048

3. Apply 80 grams (2/3 of contents) of grease from the

pack into the bearing housing.

4. Check the condition of the circlip on the end of the

half shaft and replace if necessary. Engage the exter-

nal splines on the end of the half shaft into the star-

shaped inner race of the CV joint; then grasp the half

shaft and seat it into the CV joint assembly by press-

ing it firmly into the CV joint assembly.

5. Using the boot clamp pliers, install the large diame-

ter boot clamp.



NOTE: Steps 1-5 can be used to replace the out-

board boot.



NOTE: In the outboard boot, use the final 40 grams

(1/3 of contents) of grease from the pack in the bear-

ing housing.

INSTALLING REAR DRIVE AXLE

1. Push the axle shaft into the CV coupler to release the

lock ring; then slide the drive axle into place in the

gear case.

HDX389A



NOTE: To ensure proper axle seating, give it a light

pull; the axle should remain “clipped” in place.

2. Swing the knuckle up and onto the drive axle; then

place the knuckle into place in the upper A-arm.

Secure the knuckle to the A-arm with a cap screw

and a new lock nut. Tighten to 35 ft-lb.

3. Install the hubs (see Hub in this section).

4. Install the wheels and using a crisscross pattern,

tighten the wheel nuts in 20 ft-lb increments to a final

torque of 40 ft-lb (steel wheel), 60 ft-lb (aluminum

wheel w/black nuts), or 80 ft-lb (aluminum wheel w/

chrome nuts).

5. Remove the vehicle from the support stand and

release the parking brake.

INSTALLING FRONT DRIVE AXLE

1. Push the axle shaft into the CV coupler to release the

lock ring; then position the drive axle in the gear case

and steering knuckle; then insert the ball joints into

the steering knuckles. Secure with cap screws tight-

ened to 35 ft-lb.

2. Secure the lower shock eyelet to the A-arm with a

cap screw and a new lock nut. Tighten to 35 ft-lb.

3. Install the hubs (see Hub in this section).

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды