Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 118 / 152

117

GC002A

3. While holding the actuator firmly forward, tighten

the front cap screw to hold the actuator in place; then

install but do not tighten the two remaining cap

screws.

GC001

4. Loosen the front cap screw; then tighten the cap

screw on the driveshaft side.

WC938A



NOTE: It is important to tighten this cap screw

while the others are loose to ensure proper seating of

the actuator.

5. Tighten the remaining cap screws; then connect the

electrical plug to the main harness.

6. Turn the ignition switch to the ON position and

check the operation by shifting the drive select

switch several times.

7. Secure the wiring harness to the frame with a nylon

cable tie; then install the inner fender panel.

8. Install the cap screws to secure the skid plate to the

frame.

Front Differential

REMOVING

1. With the vehicle on a lift or support stands, elevate

the wheels off the ground.

2. Remove the hubs (see Hub in this section).

3. Remove the belly panel.

4. Remove the drain plug and drain the gear lubricant

into a drain pan; then install the plug and tighten to

45 in.-lb.

PR022A

5. Disconnect the front drive actuator connector from

the main harness.

HDX291

6. Remove the lower and upper ball joint cap screws

taking care not to strip the threads on the ball joint

shaft; then using a rubber mallet, tap the end of the

axle and free it from the knuckle assembly.

PR193

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды