Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 16

Страница: 16 / 152

C. Secure the caliper holder to the knuckle with new

“

patch-lock

”

cap screws. Tighten to 20 ft-lb.

HDX345A

5. Install the wheels and using a crisscross pattern,

tighten the wheel nuts in 20 ft-lb increments to a final

torque of 40 ft-lb (steel wheel), 60 ft-lb (aluminum

wheel w/black nuts), or 80 ft-lb (aluminum wheel w/

chrome nuts).

6. Burnish the brake pads.

BRAKE DISC

Using a micrometer, measure the thickness of the brake

disc in the contact surface. If thickness is 0.125 in. or

less, the disc must be replaced. To replace the brake disc,

see Drive System – Hub.

Burnishing Brake Pads

Brake pads must be burnished to achieve full braking

effectiveness. Braking distance will be extended until

brake pads are properly burnished.

1. Choose an area large enough to safely accelerate the

vehicle to 30 mph and to brake to a stop.

2. Accelerate to 30 mph; then release the accelerator pedal

and depress the brake pedal to decelerate to 0-5 mph.

3. Repeat procedure 20 times until brake pads are bur-

nished.

Checking/Replacing V-Belt

REMOVING

1. Remove the seat, seat back, and seat base; then

remove the floor and gas tank.

2. Remove the right-side storage box.

3. Remove the cap screw, lock nut, and clamp securing

the intake duct and duct tube assembly. Then remove

the assembly.

HDX258A

4. Remove the cap screws securing the support tube to

the frame.

HDX260A

5. Remove the cap screws securing the CVT cover not-

ing the location of the different-lengthed cap screws

for installing purposes; then using a rubber mallet,

gently tap on the cover tabs to loosen the cover.

Remove the cover.

H1-017

6. Remove the nut securing the movable drive face;

then remove the face. Account for the spacer.



NOTE: Keep the drive face plate in contact with the

drive face when removing or installing the drive face

to prevent the rollers from falling out.

! WARNING

Failure to properly burnish the brake pads could lead to
premature brake pad wear or brake loss. Brake loss can
result in severe injury or death.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды