Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 7

Страница: 7 / 152

3. Check all control wires and cables for signs of wear

or fraying. Replace if necessary.

4. Change the engine/transmission oil and filter.

5. Check the coolant level and add properly mixed

coolant as necessary.

6. Charge the battery; then install. Connect the battery

cables making sure to connect the positive cable

first.

7. Check the entire brake systems (fluid level, pads,

etc.), all controls, headlights, taillight, brakelight,

and headlight aim; adjust or replace if necessary.

8. Check the tire pressure. Inflate to recommended

pressure as necessary.

9. Tighten all nuts, bolts, cap screws, and screws mak-

ing sure all calibrated nuts, cap screws, and bolts are

tightened to specifications.

10. Make sure the steering moves freely and does not

bind.

11. Check the spark plug. Clean or replace as necessary.

12. Check the air filter and the air filter housing. Clean

or replace as necessary.

CAUTION

Before installing the battery, make sure the ignition
switch is in the OFF position.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды