Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 69 / 152

H1-030

14. Place the water pump into position and secure with

two cap screws. Tighten to 8 ft-lb.



NOTE: Ensure the slotted water pump shaft is

aligned with the groove in the counter balancer shaft.

15. Install the crossover tube on the water pump and cyl-

inder head making sure the O-ring is properly posi-

tioned.

16. Place the outer magneto cover into position on the

left-side cover; then tighten four cap screws to 6 ft-lb.

Removing Right-Side

Components



NOTE: The engine/transmission does not have to be

removed from the frame for this procedure.

A. V-Belt Cover
B. Driven Pulley
C. Clutch Cover
D. Oil Pump

1. Remove the cap screws securing the V-belt cover

noting the location of the different-lengthed cap

screws for installing purposes; then using a rubber

mallet, gently tap on the cover tabs to loosen the

cover. Account for two alignment pins and a gasket.

H1-017

2. Remove and discard the nut securing the movable

drive face; then remove the face. Account for a

spacer.

CF373A

CF378

3. Remove the V-belt.

4. Remove the nut securing the fixed driven assembly;

then remove the assembly.

PR388

5. Remove the fixed drive face.

6. Remove the cap screws securing the clutch cover.

Note the location of the different-lengthed cap

screws for installing purposes. Using a rubber mallet,

carefully remove the cover. Account for two align-

ment pins.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды