Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 76 / 152

WC412

WC419

9. Turn the wing nut counterclockwise slowly allowing

the cam to contact the snap ring; then loosen slightly

and tap the cam with a plastic mallet to ensure the

snap ring is securely seated.

WC408

10. Remove the wing nut, compression yoke, and center-

ing bushing; then remove the driven pulley assembly

from the Clutch Spring Compressor.

Installing Right-Side

Components

1. Install the secondary shaft bearing housing making

sure the two alignment pins are properly positioned.

Tighten the new “patch-lock” cap screws to 28 ft-lb.

CD999

2. Install the oil pump; then tighten the screws (coated

with red Loctite #271) to 8 ft-lb.

CD988

3. Install the oil pump drive gear spacer onto the crank

balancer shaft. Grease the pin and insert it into the

shaft; then install the drive gear making sure the

raised side of the gear is facing toward the inside.

Secure the gear with the cap screw (threads coated

with red Loctite #271) and the washer. Tighten the

cap screw to 62 ft-lb.

CD992

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды