Arctic Cat HDX CREW 2017 Скачать руководство пользователя страница 87

Страница: 87 / 152

CD832B



NOTE: It will be necessary to rotate the crank bal-

ancer until the counterweight is facing away from the

crankshaft; then rotate the crankshaft clockwise into

the journal area to allow the crank balancer to be

fully seated.

4. Place the key into the crank balancer keyway; then

install the crank balancer gear making sure the align-

ment dots on the crank balancer gear and the crank-

shaft gear align.

CD826A

5. Install the driveshaft.

CC675

6. Place a washer on each end of the countershaft

assembly; then install the assembly.

CC674

7. Place a washer on the end of the gear shift shaft; then

install the shaft assembly making sure the two holes

on the end of the shaft are positioned vertically.

Install the spacer on the shift shaft.

DE677A

8. Insert the two shift forks into the sliding dogs noting

the direction of the tabs from disassembling; then

install the shift fork shaft.



NOTE: Make sure the shift fork tabs face upward

and that they are properly seated into the shift cams.

CC669

9. Install the reverse idler gear assembly noting the

positioning of the two washers, gear, bushing, and

shaft.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды