Arctic Cat HDX CREW 2017 Скачать руководство пользователя

Страница: 107 / 152

106

2. Slide the existing sender assembly (B) up and off the

fuel pump assembly housing.

XR257A

3. Keeping the float attached to the float arm, remove

the float arm from the existing fuel level sensor.

Press the float arm into the new fuel level sensor

assembly. Ensure it locks into place.

XM366



NOTE: Inspect the float for any damage or leaking

by submerging in water and looking for any air bub-

bles. Replace if damaged.

4. Install the fuel level sensor assembly onto the fuel

pump assembly housing. Once inserted, press down

to make sure it locks into place.

XR258

5. Connect the blue wires using the supplied splice con-

nectors from the fuel level sensor kit. Secure the

wires.

Installing

1. Place the fuel pump assembly into the gas tank with

a new gasket aligning the match marks; then secure

with the four screws. Tighten securely.



NOTE: It is important to install the fuel pump with

the correct orientation to ensure adequate float lever

clearance.

2. Connect the gasline hose to the fuel pump pipe and

secure with the hose clamp; then connect the electri-

cal plug to the main harness.

3. Connect the negative battery cable; then turn the

ignition switch to the ON position and verify that no

gas leaks are present, the pump runs for several sec-

onds, and the gas gauge reading is normal.

4. Start the engine to verify proper engine operation;

then shut off the engine and install the seat base, seat

back, and seat.

TILT SENSOR

Supply Voltage

1. Disconnect the three-wire connector from the sensor;

then select DC Voltage on the multimeter and con-

nect the red tester lead to the orange wire (C) and the

black tester lead to the pink/black wire (A).

CD706A

2. Turn the ignition switch to the ON position. The

multimeter should read battery voltage. If battery

voltage is not indicated, check the 30-amp fuse in the

PDM or the 10-amp power fuse, wiring harness, or

the ignition switch.

3. Remove the red tester lead and connect to the blue/

brown wire. The multimeter should read less than 0.2

DC volts. If the specified voltage is not indicated,

check wire connections at the ECM or substitute

another ECM to verify the test.

Output Voltage



NOTE: Needle adapters will be required on the mul-

timeter leads as the following tests are made with the

sensor connected.

1. Connect the three-wire plug to the sensor; then

remove the right-side mounting screw securing the

sensor to the rear frame.

! WARNING

Incorrect installation of the tilt sensor could cause sud-
den loss of engine power which could result in loss of
vehicle control resulting in injury or death.

CAUTION

Do not drop the tilt sensor as shock can damage the
internal mechanism.

Содержание HDX CREW 2017

























































































































































Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды

Arctic Cat HDX CREW 2017, Руководство по обслуживанию

Результаты поиска

Содержание HDX CREW 2017

Отзывы:

Похожие инструкции для HDX CREW 2017

Бренды по названию

Популярные бренды